Home Main Category General Firearms

Used brake rotors for targets?

1965Jeff1965Jeff Senior MemberPosts: 1,648 Senior Member
Since I have to replace my truck's rotors, I was wondering if anyone has used these as a hang-up target for 100-200 yd ranges? If the core payment is less than 20-30 dollars these would make a pretty cheap gong target... I have tried used drums but most anything will shoot through these. Since the surface on a rotor isn't flat I probably wouldn't recommend shooting at them from close range due to spalling ricochets, but at fairly long ranges should be safe enough to avoid anything zinging back at me.

Replies

  • TeachTeach Senior Member Posts: 18,428 Senior Member
    Cast iron makes a lousy target for anything more powerful than .22 rimfire. You might get away with cast lead bullets from a medium-power round like a .38 or .357 if you don't shoot closer than 100 feet or so. FMJ or any centerfire rifle round I can think of will shattter the rotor pretty quickly. The big orange "gong" shown in some of the SE shoot pics and videos is a "stump jumper", the center disc of a tractor's bush hog. It's made of fairly heavy steel, over 1/4" thick. It's got several .30 caliber holes in it from being shot from 200 yards with various centerfire rifle rounds. The small one is a forged steel boat engine flywheel nearly 2" thick. It's full of dents. It you want a reactive target to last awhile, get tempered steel at least 1/2" thick, and shoot it at moderate ranges. Closeup shots will result in lots of splashback to the firing line.
    Jerry
  • ghostsniper1ghostsniper1 Banned Posts: 2,645 Senior Member
    cpj wrote: »
    Fyi, they held up to many 7.62x54 FMJ rounds.
    I would have liked to see a closeup of those little gongs after that day. They took a poundin from everybody.
  • 1965Jeff1965Jeff Senior Member Posts: 1,648 Senior Member
    Thanks for the info on the inexspensive steel targets, will investigate google on those. I have 8x8 3/4in steel target that has been around for many years, only penetrated by a 180 gr nosler partition from a 300win mag. 30-06 will dimple it and I just turn it 180 every now and then. I welded a plate over the hub hole from scrap and bent a chunk of rebar to act as a holder, nothing much going on this PM so I think I will haul new target to the pasture and see how it holds up against the AR...:tooth:
  • FisheadgibFisheadgib Senior Member Posts: 5,797 Senior Member
    Actually those plates were 6"x3/8" and I paid 17.00 each for them at Widener's and all four came in a flat rate box. In the next few days I'll post a pic of them as I was supprised that there aren't even any dents in them. I'll redo them with heavier chain before I use them again but otherwise I was very happy with them. I was curious to find out what the heaviest caliber they had been hit with. I'm going to buy a couple more of them in the 8"x1/2" thick version. I think hanging loosly on the chains helped keep them getting damaged although they are AR500 steel.
    snake284 wrote: »
    For my point of view, cpj is a lot like me
    .
  • HAWKENHAWKEN Senior Member Posts: 1,720 Senior Member
    If you miss, you can always claim that your shot went through the center hole, LOL.......Robin
    I don't often talk to people that voted for Obama, but when I do I order large fries!
    Life member of the American Legion, the VFW, the NRA and the Masonic Lodge, retired LEO
  • bruchibruchi Senior Member Posts: 2,581 Senior Member
    Do a search on ebay for AR500 this are fine to shoot with all common handgun and most rifle rounds and last forever! You will be surprised at the great prices and most sellers will stuff as many as will fit on an USPS Flat Rate box making shipping dirt cheap.
    If this post is non welcomed, I can always give you a recipe for making "tostones".
  • bullsi1911bullsi1911 Moderator Posts: 12,043 Senior Member
    cpj wrote: »
    Weidners has some 4inch x 3/8 hardened steel targets for about 15 bucks. I know for a fact they are....bullet proof. We shot the heck out of them at Jerrys last weekend. WELL worth the money.

    Link?
    To make something simple is a thousand times more difficult than to make something complex.
    -Mikhail Kalashnikov
  • tennmiketennmike Senior Member Posts: 27,457 Senior Member
      I refuse to answer that question on the grounds that I don't know the answer”
    ― Douglas Adams
  • coolgunguycoolgunguy Senior Member Posts: 6,632 Senior Member
    Teach wrote: »
    FMJ or any centerfire rifle round I can think of will shattter the rotor pretty quickly.

    :that: Fairly 'brittle' stuff.
    "Bipartisan" usually means that a bigger than normal deception is happening.
    George Carlin
  • jbohiojbohio Senior Member Posts: 5,615 Senior Member
    I have it on good authority that AR500 targets aren't fazed by 300 or 338WM.
    I wasn't allowed to shoot them with the RUM.
Sign In or Register to comment.
Magazine Cover

GET THE MAGAZINE Subscribe & Save

Temporary Price Reduction

SUBSCRIBE NOW

Give a Gift   |   Subscriber Services

PREVIEW THIS MONTH'S ISSUE

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Get the top Guns & Ammo stories delivered right to your inbox every week.

Advertisement